Видео

Thanks again for another good video. Thank you

To save you time, find another video to learn from.

Thanks very much I learned a lot from your videos and thanks for sharing. Watching all the way from Papua New Guinea 😊😊😊😊😊

Good job sir

Your good. I'am a retired ASE Tech and instructor . You understand the concept and know how to clearly deliver instructions on how to diagnosis and repair.

Thanks great video.

Very very good!!

Isnt it a little windy?

Maybe it was a trick of the camera but it sure looked like the yellow corvette and a white car were very close to you spraying the clear coat. Hard to believe with the wind blowing that there wasn’t overspray going everywhere.

Talk to much

Worlds longest yellow light

Great info, thanks. I'm working on a 2008 Kia Sportage with a bank 1 sensor 1 (upstream above cat) slow response error, P0133. Over a few years a few shops have worked on it, but could not figure it out. Both sensors were replaced with OEM sensors. OK so I get the idea to test the wiring. The ground I am good with. For the signal line, hook up a scanner introduce power and see if that gets through the ECU to the scan tool. I am just concerned about putting 12 volts in there as think these sensors use mili amps. Could anyone comment on that. Thanks.

Hi Lexus 3uz-fe 4.3 2006 The cars starts good, runs good, but will driving the throttle just suddenly close, no refs just idles, if I press on peddle no response, have to switch off and restart, then it runs again for n few kilometers, before it das it again 😡

Nice video

I love how every youtube mechanic says do it per your manufacter specs but then skips them actually torqueing to their specs lol they aint torquing shit... Buy ur cars manufacturer pubs tho and thats where u actually could get that in depth info but if u bought that pub u dont need these video tho fun to watch

No current flow, How does the test light shine with an open circuit?

I am watching this video after being abused by a screw and having to give up changing my brakes because i could not remove the caliper.

So at 200,000 the transmission is doomed if the oil is dark.

Finishing up a rebuild on the same engine now but as I put the first timing roller in with the flange it’s contacting a thread post on the oil pump. Anyone else experiencing this? Any thoughts?

I have a question for you. If you remove the wire between the starter motor and solenoid. Then supply the 12V to the signal wire as you demonstrated. Why wont the solenoid itself operate and motor not turn??? The starter motor obviously can't run, but why doesn't the solenoid retract back a push the drive gear out ???

Thank you so much!

That is never do,if y using like this tools use impact key and T part than y have a 50% stronger and no sleping key,dont use a 72 tits,better is 24 then y never hapend to destroy like on this video,i m sorry my english is bad but who is master he understud me and hamer god no,just y destroy tool,they snap or brake and use a brain,God is give us to think no brned him

before the clear coat, do we need to make sure that all the lines of spray paint have peffectly overlaped , or is that not necessay. thats the part that worries me.

You bead breaker needs to be moved up. Rewatch your video and notice that the bead breaker is moving away from the tire because it wants to be 90 degrees from where it is attached. So if you move it out as far as it will go it won't slide away from the rim like it has been doing.

😢

reach out to me, you need Griot's fast correction cream. i can hook you up!

Great video, and a historic one! The video where he went from "Hey what's up RUclips!" to "Hey what's up do-it-yourselfers!"

First video I’ve ever seen with a road test after replacing a part thank you for that

The painting should be done indoors, so the leaves and bugs don't become part of the finish.

Most useful information about changing a head gasket or a used working engine 👍

I just replaced my canister valve and it's already bursting through again.

11 years later I think this is going to fix my issue.. I'm throwing the exact p0411 code I just replaced tcm and neutral position switch this is my last gremlin thank you!!!

I have done this with a couple of gel batteries from sears. About twice a year and it seems to work if I put my charger on a 100 amp/start boost! About for a few minutes only about three minutes then let rest ten minutes and power it up again for another round perhaps three or four times!

Why does o2 sensor pigtail have yellow liquid in it?

just what I needed to hear thank you for your video

yes thats right once saved myself a lot of money when a main dealer diagnosed a bad wheel bearing. i went to another dealer and it turned out to be caused by a tyre not being round

Great video

I have a 2.2 vtec accord from 1997 and on cold starts my idle will surge unless I hold the pedal very slightly to stop it from doing so until it gets warm then it idles perfectly fine. I’m not having overheating issues but I heard on these years idle is connected to the coolant system so I am curious what you think it may be thanks

I love how I looked up “why are you shaking” on RUclips to find the video of sweetie and jack harlow. And I actually just find a video that addresses a real problem with my car 😂😂 now I know why my car is shaking at highway speed 💀 cool

I always liked your whiteboard bc it’s really great details, great improvement!

on my 1998 chevrolet blazer 4 wheels drive leaking transmission and my SUV will not moved at in any gears so comment me back. Thanks you?

Whey do my truck have to warm up completely for transmission to not slip out of gear

Thank you!

Video to long

I don’t understand is their a part two or something? U only did 1 out of 2 scratches 🤣🤣🤦🏻‍♂️ did you forget haft way trough making the video?

Thank you for the video. Chasing a lean condition M54B25 .-.

You are a great instructor! Thanks

Greta tip … can I do this in the inside relay box ? that’s where my main fuses are.

Thanks brother

Nice